全文获取类型
收费全文 | 1119篇 |
免费 | 263篇 |
国内免费 | 286篇 |
专业分类
航空 | 868篇 |
航天技术 | 297篇 |
综合类 | 107篇 |
航天 | 396篇 |
出版年
2024年 | 5篇 |
2023年 | 24篇 |
2022年 | 45篇 |
2021年 | 61篇 |
2020年 | 62篇 |
2019年 | 87篇 |
2018年 | 73篇 |
2017年 | 60篇 |
2016年 | 80篇 |
2015年 | 63篇 |
2014年 | 83篇 |
2013年 | 72篇 |
2012年 | 67篇 |
2011年 | 87篇 |
2010年 | 68篇 |
2009年 | 59篇 |
2008年 | 52篇 |
2007年 | 75篇 |
2006年 | 62篇 |
2005年 | 48篇 |
2004年 | 44篇 |
2003年 | 41篇 |
2002年 | 30篇 |
2001年 | 41篇 |
2000年 | 30篇 |
1999年 | 38篇 |
1998年 | 45篇 |
1997年 | 27篇 |
1996年 | 21篇 |
1995年 | 24篇 |
1994年 | 19篇 |
1993年 | 21篇 |
1992年 | 18篇 |
1991年 | 7篇 |
1990年 | 8篇 |
1989年 | 10篇 |
1988年 | 4篇 |
1987年 | 5篇 |
1986年 | 2篇 |
排序方式: 共有1668条查询结果,搜索用时 15 毫秒
41.
刘艳红 《中国民航学院学报》2004,22(5):38-42
将三维弹性材料的H-R变分原理引入到具有机-电耦合效应的三维压电弹性材料圆柱壳问题中,建立了对应于正交各向异性压电材料圆柱壳的Hamilton型广义变分原理。通过变分运算得到了柱坐标系下的状态向量方程,该状态向量方程也是Hamilton正则方程。最后指出纯正交各向异性弹性材料壳Hamilton型广义变分原理是变分公式的特例。变分原理的建立将有利于压电材料圆柱壳静力学和动力学问题的有限元方法或半解析法的推导。 相似文献
42.
直接力控制的特征结构配置法 总被引:3,自引:0,他引:3
以现代控制理论和飞行力学原理为基础,针对直接力控制器设计中存在的模态耦合问题,提出一种应用状态反特征结构配置进行解耦的方法,并出相应的公式。分析表明,用此方法对系统的极点和特征向量可以进行希望的配置。并能达到设计要求,同时仿真结果说明,用状态反馈特征结构配置法设计的控制系统比用线性二次型调节器(LQR)方法设计的控制系统解耦性能好,响应速度快,并且解决了输出反馈特征结构配置不能确保闭环系统稳定的问题。 相似文献
43.
44.
主状态量模型是基于发动机故障方程的发动机故障诊断的一种十分有效的方法,它在发动机故障诊断上的成功应用已为大量实例所证实。发动机故障诊断主状态量模型的一个技术关键就是合理解的选择问题。本文给出了选择合理解的基本原则。这些原则可以有效地提高合理解选择的确定性和故障诊断的故障分辨率。对于JT9D发动机的大量故障实例利用主状态量模型(加权最小二乘法)进行了检验。故障诊断的成功率达90%以上,并且得到了许多有用的信息,文中给出了24个实例的故障诊断结果以及故障趋势分析的典型例子。 相似文献
45.
46.
非线性气动模型结构确定是飞行器参数辨识中极其重要的问题。首先给出了非线性气动模型的数学描述,在此基础上,以导弹纵向及侧向运动方程为例,首次系统地分析了有控飞行器非线性气动模型结构确定中必然存在的共线性问题。频域分析过程清晰地表明在通常的试验情况下,m_z~α及m_z~(ω_z)是不可单独辨识的,从理论上解释了国内外一直不单独辨识它们的原因所在。指出原有的模型结构确定方法,如AIC准则,逐步回归等已不再适用于非线性气动模型结构的确定。同时对参数的可辨识性也作了一定的讨论。 相似文献
47.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
48.
49.
50.